View T260XW03-V2_5318912.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

?copyright au optronics, inc. january 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 1/28 no reproduction and redistribution allowed document version : 0.4 date : 2007/07/31 product description: t260xw03 tft-lcd panel with ro hs guarantee auo model name: t260xw03 v2 customer part no/project name : customer signature date auo 2007/07/31 www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 2/28 no reproduction and redistribution allowed product specifications 26? wxga color tft-lcd module model name: t260xw03 v2 ( ) preliminary specifications (*) final specifications www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 3/28 no reproduction and redistribution allowed contents interface connections 3-2 color input data refernece 3-5 precautions 9 packing (green mark description) 8 safety 7-2 cover contents record of revisions general description 1 absolute maximum ratings 2 electrical specifications 3 electrical charactreistics 3-1 signal timing specifications 3-3 signal timing waveforms 3-4 power sequence 3-6 optical sfecifications 4 mechanical characteristics 5 6 reliability international standards 7-1 item no emc 7 www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 4/28 no reproduction and redistribution allowed record of revision version date no old description new description remark 0.0 07?/04/11 - first draft 0.1 07?/05/24 all update tbd items 0.2 07?/06/11 5 updated me outline drawing 0.3 07?/07/18 3-3 update timing table: old ? update timing table: new ? 0.4 07?/07/31 5 updated me outline drawing www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 5/28 no reproduction and redistribution allowed 1. general description this specification applies to the 26.0 inch color t ft-lcd module t260xw03 v2. this lcd module has a tft active matrix type liquid crystal panel 1366x768 pixels, and diagonal size of 26.0 inch. this module support s 1366x768 xga-wide mode (non-interlace). each pixel is divided into red, green and blue sub- pixels or dots which are arranged in vertical stripes. gray scale or the brightness o f the sub-pixel color is determined with a 8-bit (6bit+frc) gray scale signal for each dot. the t260xw03 v2 has been designed to apply the 8-bi t 1 channel lvds interface method. it is intended to support displays where hi gh brightness, wide viewing angle, high color saturation, and high color depth are ver y important. the t260xw03 v2 model is rohs verified, which can b e distinguished on panel label. * general information items specification unit note active screen size 26.0 inches display area 575.769 (h) x 323.712 (v) mm outline dimension 626.0(h) x 373.0(v) x 42.2 (d) mm with inverter driver element a-si tft active matrix display colors 16.7m colors number of pixels 1366 x 768 pixel pixel pitch 0.4215 mm pixel arrangement rgb vertical stripe display mode normally white surface treatment ag, 3h haze= 25 www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 6/28 no reproduction and redistribution allowed 2. absolute maximum ratings the following are maximum values which, if exceeded , may cause permanent damage to the unit. item symbol min max unit conditions input voltage of lcd power vin -0.3 5.5 [volt] note 1 input voltage of signal vsignal -0.3 4 [volt] note 1 blu input voltage vddb 21.6 26.4 [volt] note 1 blu brightness control voltage vblon 0 5.25 [volt] note 1 internal pwm dimming control voltage pdim 0 5.25 [volt] note 1 operating temperature top 0 +50 [ o c] note 2 operating humidity hop 10 90 [%rh] note 2 storage temperature tst -20 +60 [ o c] note 2 storage humidity hst 10 90 [%rh] note 2 note 1: duration:50 msec. note 2 : maximum wet-bulb should be 39 and no condensation. the relative humidity must not exceed 90% non-conde nsing at temperatures of 40 or less. at temperatures greater than 40 , the wet bulb temperature must not exceed 39 . www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 7/28 no reproduction and redistribution allowed 3. electrical specifications the t260xw03 v2 requires two power inputs. one is e mployed to power the lcd electronics and to drive the tft array and liquid c rystal. the second input power for the blu, is to power inverter.. 3-1 electrical characteristics parameter values unit notes min typ max lcd: power supply input voltage vcc 4.5 5 5.5 vdc 1 power supply input current icc 0.7 1 a 2 power consumption pc - 3.5 5 watt 2 inrush current i rush - - 3 apeak 3 differential input high threshold voltage vth 100 mv 4 differential input low threshold voltage vtl -100 mv 4 lvds interface common input voltage vicm 1.10 1.25 1.40 v input high threshold voltage vih (high) 2.4 3.3 3.6 vdc cmos interface input low threshold voltage vil (low) 0 0.7 vdc backlight power consumption pddb 66 72 watt 8 total power consumption 69.5 life time 50,000 60,000 hours 9 www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 8/28 no reproduction and redistribution allowed note : 1. the ripple voltage should be controlled under 10% o f v cc 2. vcc= 5.0v, = v f 60hz, fclk=85mhz , 25 , test pattern : white pattern 3. measurement condition : trush = 470 us 10% 90% vcc gnd 4. vcim = 1.2v vth vcim vtl 0v 5. the performance of the lamp in lcm, for example lif e time or brightness, is extremely influenced by the characteristics of the dc-ac inve rter. so all the parameters of an inverter should be carefully designed so as not to produce t oo much leakage current from high-voltage output of the inverter. when you design or order th e inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter (no lighting, flicker, etc) never occurs. when you confirm it, the lcd assembly shoul d be operated in the same condition as installed in your instrument. 6. do not attach a conducting tape to lamp connecting wire. if the lamp wire attach to conducting tape, tft-lcd module have a low luminance and the i nverter has abnormal action because leakage current occurs between lamp wire and conduc ting tape. 7. the relative humidity must not exceed 80% non-conde nsing at temperatures of 40 or less. at temperatures greater than 40 , the wet bulb temperature must not exceed 39 . when operate at low temperatures, the brightness of ccfl will drop and the life time of ccfl will be reduced. 8. the measured data is without boost function 9. lifetime is defined and judged when analog and pwm dimming are maximum values www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 9/28 no reproduction and redistribution allowed 3-2 interface connections lcd panel driving signal connector type and pin ass ignment are as follows: connector on panel: fi-e30s (manufactured by jae) or equivalent mating connector: fi-30c2l (manufactured by jae) or equivalent note: 1. all gnd (ground) pins should be connected together and should also be connected to the lcd?s metal frame. all vcc (power input) pins shoul d be connected together. 2. for pin 1,2,3,20 and 22, panel will not damage if n egligently connect these pins to high or low. pin no symbol description note 1 n.c. no connection ( auo internal test pin) 2 n.c. no connection ( auo internal test pin) 3 n.c. no connection ( auo internal test pin) 4 gnd ground 5 rx0- lvds channel 0 [polarity: negative] 6 rx0+ lvds channel 0 [polarity: positive] 7 gnd ground 8 rx1- lvds channel 1 [polarity: negative] 9 rx1+ lvds channel 1 [polarity: positive] 10 gnd ground 11 rx2- lvds channel 2 [polarity: negative] 12 rx2+ lvds channel 2 [polarity: positive] 13 gnd ground 14 rxclk- lvds clock [polarity: negative] 15 rxclk+ lvds clock [polarity: positive] 16 gnd ground 17 rx3- lvds channel 3 [polarity: negative] 18 rx3+ lvds channel 3 [polarity: positive] 19 gnd ground 20 n.c. no connection ( auo internal test pin) 21 lvds option* low for jeida, high/open for ns 22 n.c. no connection ( auo internal test pin) 23 gnd ground 24 gnd ground 25 gnd ground 26 vdd (+5v) 5v, dc, regulated 27 vdd (+5v) 5v, dc, regulated 28 vdd (+5v) 5v, dc, regulated 29 vdd (+5v) 5v, dc, regulated 30 vdd (+5v) 5v, dc, regulated www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 10/28 no reproduction and redistribution allowed lvds option = high or open lvds option = low www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 11/28 no reproduction and redistribution allowed backlight connector pin configuration electrical specification spec item symb. condition min typ max units note. input voltage vddb - 21.6 24 26.4 vdc input current iddb vddb=24v 2.5 2.75 3.05 adc 1 input power pddb vddb=24v 66 72 w 1 inrush current irush vddb=24v 3.4 adc 2 on vddb=24v 2 5 5.25 on/off control voltage vblon off vddb=24v 0 - 0.8 vdc on/off control current iblon vddb=24v 0 1.5 madc output frequency fbl vddb=24v 43.5 45 46.5 khz max vddb=24v 3.3 1 dimming control voltage pdim min vddb=24v 0 vdc note1. pdim = 3.3v (ta = 25+-5 , turn on for 45 minutes) note2. measurement condition rising time = 20ms (vdd : 10%~90%) input specification cn1: 20022wr-14l(yeon-ho) or compatible pin no. symbol description default 1 vddb operation voltage supply, +24v dc regulated 24v 2 vddb operation voltage supply, +24v dc regulated 24v 3 vddb operation voltage supply, +24v dc regulated 24v 4 vddb operation voltage supply, +24v dc regulated 24v 5 vddb operation voltage supply, +24v dc regulated 24v 6 gnd ground and current return gnd 7 gnd ground and current return gnd 8 gnd ground and current return gnd 9 gnd ground and current return gnd 10 gnd ground and current return gnd 11 n.c this pin is floating inside ; n.c 12 vblon bl on-off: high (3.3v) for bl on , open/lo w (0v) for bl off off 13 pdim internal pwm ; 0v (gnd) min lum / 3.3v (open)max lu m 100% 14 n.c this pin is floating inside ; n.c www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 12/28 no reproduction and redistribution allowed 3-3 signal timing specifications this is the signal timing required at the input of the user connector. all of the interface signal timing should be satisfied with the followin g specifications for it?s proper operation. * timing table de only mode signal item symbol min type max unit period tv 784 806 1063 th active tdisp (v) ? 768 ? th vertical section blanking tblk (v) 16 38 295 th period th 1434* 1560 2000 tclk active tdisp (h) ? 1366 ? tclk horizontal section blanking tblk (h) 68 194 634 tclk period tclk 11.36 13.16 18.19 ns clock frequency freq 55 76 85 mhz vertical frequency frequency vs 48 60 75 hz horizontal frequency frequency hs 39.45 61.65 khz 1.) display position is specific by the rise of de signal only. horizontal display position is specified by the ris ing edge of 1 st dclk after the rise of 1 st de, is displayed on the left edge of the screen. vertical display position is specified by the rise of de after a ?low? level period equivalent to eigh t times of horizontal period. the 1 st data corresponding to one horizontal line after th e rise the of 1 st de is displayed at the top line of screen. 3.) if a period of de ?high? is less than 1366 dclk or less than 768 lines, the rest of the screen displays black. 4.) the display position does not fit to the screen if a period of de ?high? and the effective data pe riod do not synchronize with each other. www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 13/28 no reproduction and redistribution allowed 3-4 signal timing waveforms th tdisp(v) tv de rgb data 768 line invalid data invalid data 1 line 2 line 3 line 768 line 4 line tclk clk de rgb data pixel 1366 invalid data pixel 1 pixel 2 pixel 3 pixel 4 pixel 5 pixel 6 pixel 1366 invalid data pixel 1 pixel 2 th tdisp(h) www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 14/28 no reproduction and redistribution allowed 3-5 color input data reference the brightness of each primary color (red, green an d blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the bri ghter the color. the table below provides a referen ce for color versus data input. color data reference input color data red msb lsb green msb lsb blue msb lsb color r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b2 b1 b0 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 basic color white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ---- red(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 ---- green(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 green green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ------- blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 blue blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v 2 - spec. ver 0.4 15/28 no reproduction and redistribution allowed 3-6 power sequence 3.6.1 power sequence for lcd 10% 90% 90% 10% t1 t2 t3 t4 t5 t6 t7 lamp on valid data power supply for lcd signal backlight values parameter min. typ. max. units t1 0.5 - 20 ms t2 20 - 50 ms t3 800 - - ms t4 200 - - ms t5 0.5 - 50 ms t6 - - 300 ms t7 1 - - s apply the lamp voltage within the lcd operating ran ge. when the backlight turns on before the lcd operation or the lcd turns off before the backlight turns off, the display may momentarily become abnormal. caution : the above on/off sequence should be applied to avo id abnormal function in the display. in case of handling, make sure to turn off the power w hen you plug the cable into the input connector or pull the cable out of the connector. www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 16/28 no reproduction and redistribution allowed 3.6.2 power sequence for inverter values parameter min. typ. max. units t1 20 - - ms t2 50 - - ms t3 200 - - ms t4 0 - - ms t5 60 - - ms t6 - - 10 ms note: in case of t3<20 0ms, uniformity and optical performance are not gua ranteed. but it will not damage power supplier and inverter. www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 17/28 no reproduction and redistribution allowed 4. optical specifications optical characteristics are determined after the un it has been ?on? and stable for approximately 30 minutes in a dark environment at 2 5 . the values specified are at an approximate distance 50cm from the lcd surface a t a viewing angle of and equal to 0. fig.4-1 optical measurement equipment and method values parameter symbol min. typ. max. units notes contrast ratio cr 650 800 1 surface luminance, white lwh 400 500 cd/ O 2 luminance variation white 9 p 1.3 3 response time 8 16 4 rise time ton 6 ms (ton+toff) decay time toff 2 ms color coordinates red r x 0.643 r y 0.337 green g x 0.294 g y 0.597 blue b x 0.144 b y 0.065 white w x 0.280 w y typ.-0.03 0.290 typ.+0.03 viewing angle cr>10 x axis, right( =0) r 65 80 degree 5, 6 x axis, left( =180) l 65 80 degree 5, 6 y axis, up( =90) u 65 80 degree 5, 6 y axis, down ( =0) d 65 80 degree 5, 6 pr880 or equivalent www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v 2 - spec. ver 0.4 18/28 no reproduction and redistribution allowed note : 1. contrast ratio (cr) is defined mathematically as : 2. surface luminance is luminance value at point 5 across the lcd surface 50cm from the surface with all pixels displaying white. from more informa tion see fig 4-2. when vddb = 24v, iddb = 2.7a. l wh =lon5. where lon5 is the luminance with all pixels displaying white at center location point 5. 3. the variation in surface luminance, white is defined (center of screen) as: white(9p) = maximum(l on1 , l on2 ,?,l on9 )/ minimum(l on1 , l on2 ,?l on9 ) 4. response time is the time required for the displ ay to transition from white(lon) to black(loff) (decay time, tr d =toff ) and from black(loff) to white(lon) (rise ti me, tr r =ton ). the response time interval is between the 10% and 90% of 1 st frame amplitudes. for additional information see fig 4-3. 5. viewing angle is the angle at which the contrast ratio is greater than 10. the angles are determined for the horizontal or x axis and the ver tical or y axis with respect to the z axis which is normal to the lcd surface. for more information see fig 4-5. 6. to be measured with a viewing cone of 1by topco n luminance meter eldim ez contrast 160d . fig. 4-2 luminance fig.4-3 response time contrast ratio (cr)= brightness on the white (lon5 ) brightness on the black (loff5) state 1 2 3 4 5 6 7 8 v h v/6 v/2 h/2 h/6 9 tr d tr r www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 19/28 no reproduction and redistribution allowed fig.4-4 viewing angle www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v 2 - spec. ver 0.4 20/28 no reproduction and redistribution allowed 5. mechanical characteristics the contents provide general mechanical characteris tics for the model t260xw03 v0. in addition the figures in the next page are de tailed mechanical drawing of the lcd. horizontal (typ.) 626.0mm vertical (typ.) 373.0mm outline dimension depth (typ.) 42.2mm* (w/i inverter & shielding) 30.3mm (w/o inverter & shielding) horizontal (typ.) 580.8 1.0 mm bezel opening vertical (typ.) 328.8 1.0 mm horizontal 575.769mm active display area vertical 323.712mm weight 4500g (typ.) surface treatment anti-glare, 3h *depth: typ.=42.2mm ; max. = 42.3mm www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v 2 - spec. ver 0.4 21/28 no reproduction and redistribution allowed front view www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 22/28 no reproduction and redistribution allowed rear view www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v 2 - spec. ver 0.4 23/28 no reproduction and redistribution allowed 6. reliability environment test condition no test item condition 1 high temperature storage test ta=60 240h 2 low temperature storage test ta=-20 240h 3 temperature humidity bias ta=50 80%rh 240h 4 low temperature operation test ta=0 240h 5 high temperature operation test ta=50 240h 6 vibration test (non-operating) wave form: random vibration level : 1.5g rms bandwidth : 10-300hz duration: x, y, z 30min 11 mins/cycle one time each direction, 30 min for each time 7 shock test (non-operating) shock level: 50g waveform: half since wave, 20ms direction: x, y, z one time each direction 8 vibration test (with carton) random vibration:10~200hz,1.5g,30minutes in each x,y,z direction 9 drop test (with carton) height: 53.3cm 1 corner, 3 edges, 6 surfaces (astmd4169-i) note 1 : evaluation should be tested after storage at room temperature for one hour. note 2 : there should be no change which might affect the practical display function when the display quality test is conducted under normal oper ating condition. note 3 : judgment: function test and display ok. www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v 2 - spec. ver 0.4 24/28 no reproduction and redistribution allowed 7. international standards 7-1. safety (1) ul6500, underwriters laboratories, inc. (auo fi le number : e204356) standard for safety of information technology equip ment including electrical business equipment. (2) can/csa c22.2 no. 950-95 third edition, canadia n standards association, jan. 28, 1995 standard for safety of information technology equip ment including electrical business equipment. (3) en60950 : 1992+a2: 1993+a2: 1993+c3: 1995+a4: 1 997+a11: 1997 iec 950: 1991+a1: 1992+a2: 1993+c3: 1995+a4:1996 iec 60065 european committee for electro technical standardiz ation (cenelec) european standard for safety of information technol ogy equipment including electrical business equipment. 7-2. emc a) ansi c63.4 ?methods of measurement of radio-nois e emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. ?american national standards institute(ansi), 1992 b) c.i.s.p.r ?limits and methods of measurement of radio interface characteristics of information technology equipment.? international special commit tee on radio interference. c) en 55022 ?limits and methods of measurement of r adio interface characteristics of information technology equipment.? european committee for elect rotechnical standardization. (cenelec), 1998 www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 25/28 no reproduction and redistribution allowed 8. packing label sample green mark description: for pb free products, auo will add for identification. for rohs compatible products, auo will add for identification. note. the green mark will be present only when the green documents have been ready by auo internal green team. (the definition of green desig n follows the auo green design checklist .) carton label packing size: carton box: 720(l)mm*324(w)mm*470(h)mm ; 36kg pallet size: 980(l)mm*730(w)mm*120(h)mm shipping volume per pallet: by air: (3*1)*2 layers, one pallet put 6 boxes, total 30ps module. by sea: (3*1)*2 layers per pallet, to pile up two layers pallets in container 12 boxes, total 60ps module. carton no: customer no: made in xxxxx model no: t260xw03 vx *pm100-01a1600001* qty: 5 part no: 97.26t04.xxx au o ptronics www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 26/28 no reproduction and redistribution allowed packing process 5pcs modules cushion set 1pcs module/esd bag module 5pcs / 1 carton h tape www.datasheet.co.kr datasheet pdf - http://www..net/
appendix 9. precautions please pay attention to the followings when you use this tft lcd module. 9-1 mounting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so t hat uneven force (ex. twisted stress) is not applied to module. and the case on which a module i s mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protectiv e plate to the surface in order to protect the polarizer. transparent protective plate should have sufficient strength in order to the resist externa l force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials fo r the cover case are not desirable because the former generates corrosive gas of attacking the pol arizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizer s with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clo thes with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth. (some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gen tly with absorbent cotton or other soft materials like chamois soaks with petroleum benzene . normal-hexane is recommended for cleaning the adhesives used to attach front/ rear p olarizers. do not use acetone, toluene and alcohol because they cause chemical damage to the p olarizer. (8) wipe off saliva or water drops as soon as possi ble. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2 operating precautions (1) the spike noise causes the mis-operation of cir cuits. it should be lower than following voltage: v=200mv(over and under shoot voltage) (2) response time depends on the temperature. (in l ower temperature, it becomes longer..) (3) brightness depends on the temperature. (in lowe r temperature, it becomes lower.) and in lower temperature, response time (required time that brightness is stable after turned on) becomes longer. (4) be careful for condensation at sudden temperatu re change. condensation makes damage to polarizer or electrical contacted parts. and after fading condensation, smear or spot will occur. (5) when fixed patterns are displayed for a long ti me, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppression to the electromagnetic interference shall be done by system manufacturers. grounding and shielding methods may be important to minimize the interface. 9-3 electrostatic discharge control since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make certain that treatment persons are connected to gro und through wrist band etc. and don?t touch interface pin directly. 9-4 precautions for strong light exposure strong light exposure causes degradation of polariz er and color filter. 9-5 storage when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the m odule to sunlight or fluorescent light. keep the temperature between 5 and 35 a t normal humidity. (2) the polarizer surface should not come in contac t with any other object. it is recommended that www.datasheet.co.kr datasheet pdf - http://www..net/
?copyright au optronics, inc. january, 2007 all rights reserved. t260xw03 v2 - spec. ver 0.4 28/28 no reproduction and redistribution allowed they be stored in the container in which they were shipped. 9-6 handling precautions for protection film (1) the protection film is attached to the bezel wi th a small masking tape. when the protection film i s peeled off, static electricity is generated between the film and polarizer. this should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) when the module with protection film attached i s stored for a long time, sometimes there remains a very small amount of flue still on the bezel afte r the protection film is peeled off. (3) you can remove the glue easily. when the glue remai ns on the bezel or its vestige is recognized, pleas e wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexan e. www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of T260XW03-V2

	To Download T260XW03-V2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .